SuSE 10.0 goes Netzwerk

Anzeige

AW: SuSE 10.0 goes Netzwerk

Verstehe ich nu alles falsch oder muß ich bei wpa Verschlüsselung erst das wpa installieren und dann das ndiswrapper?

 

AW: SuSE 10.0 goes Netzwerk

Das WPA ist die Verschlüsselungsart mit der der Router das WLAN-Signal verschlüsselt.
Das stellst du ja am Router ein.
Du musst nach der configuration des -simulierten- WLAN-Adapter (USB-Stick), der nach der install. - über ndiswrapper -als wlan0 eingerichtet wird, mitteilen mit welcher Verschlüsselung dein Router arbeitet.

 

AW: SuSE 10.0 goes Netzwerk

Ja dann habe ich damit schon mal Pech.

 

AW: SuSE 10.0 goes Netzwerk

Das bezieht sich auf deinen Lüfter ?

 

AW: SuSE 10.0 goes Netzwerk

Kopf nicht hängen lassen, nun müssen wir schwerere Geschütze auffahren.

1. Was spricht lsmod?

Müsste etwa so aussehen:

Code:

gentoo ~ # lsmod
Module                  Size  Used by
i2c_dev                12160  0
eeprom                  8272  0
w83627hf               30032  0
hwmon_vid               2944  1 w83627hf
i2c_isa                 6208  1 w83627hf
i2c_viapro             10072  0

Diese Sachen hängen mitm Power Managment zusammen. Ebenfalls ist zu beachten, dass im Kernel die entsprechende Power Governors aktiviert sind.

Dann braucht man das Tool lm_sensors. Nach der Installation müsste das so aussehen:

Und spätestens damit muss es gefunden werden, hier z.B. bei mir:

Code:

Driver `w83627hf' (should be inserted):
  Detects correctly:
  * ISA bus address 0x0290 (Busdriver `i2c-isa')
    Chip `Winbond W83697HF Super IO Sensors' (confidence: 9)


I will now generate the commands needed to load the I2C modules.

Wiederum ist zu beachten, dass im Kernel I2C Support aktiv ist, sonst funktioniert die ganze Schose nicht. Anschliessend noch ein 'modules-update' und fertig. Abschliessend belohnt einem dann KDE mit ksensors:


Im 2. Feld ist die aktuelle Drehrate des Lüfters zu sehen, im 4 Feld die CPU Temp. Wenn man soweit ist, funktioniert auch (zumindest bei mir) die Autoanpassung.

 

AW: SuSE 10.0 goes Netzwerk

@ BlackWolf

Was du da beschreibst findet sich in der SuSE unter :

KSensor
Sensor

nach der Installation zu finden : Dienstprogramme/ksensor

Das ist aber nur "monitoring" - kein "händischer" Zugriff.
Lechuk braucht aber sowas wie "SpeedFan", zum regeln der Lüfterdrehzahl.


Ich bin grade aufdasgestossen --> Klick

Ist zwar aus dem Amilo-Forum, stehen aber ein paar interessante Ansätze drin.

Siehst du, bist nicht der einzige mit dem Problem.

@ Lechuk

Welche "Antwort" kommt auf :

Code:

modprobe -l fan

 

AW: SuSE 10.0 goes Netzwerk

modprobe -l fan command not found jetzt kommt das: linux:~ # modprobe -l fan /lib/modules/2.6.13-15-default/kernel/drivers/acpi/fan.ko

Code:

holger@linux:~> lsmod Module Size Used by speedstep_lib 4228 0 freq_table 4612 0 edd 9824 0 snd_pcm_oss 59168 0 snd_mixer_oss 18944 1 snd_pcm_oss snd_seq 51984 0 snd_seq_device 8588 1 snd_seq snd_intel8x0 33408 1 snd_ac97_codec 90876 1 snd_intel8x0 snd_ac97_bus 2432 1 snd_ac97_codec snd_pcm 93064 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec snd_timer 24452 2 snd_seq,snd_pcm snd 60420 10 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer soundcore 9184 1 snd snd_page_alloc 10632 2 snd_intel8x0,snd_pcm lp 11460 0 parport_pc 38980 1 parport 33864 2 lp,parport_pc af_packet 21384 0 sg 35744 0 st 38944 0 sd_mod 18576 0 sr_mod 16420 0 scsi_mod 131304 4 sg,st,sd_mod,sr_mod subfs 7552 0 ipv6 242752 10 joydev 9408 0 button 7056 0 battery 10244 0 ac 5252 0 generic 4484 0 [permanent] ohci1394 32820 0 ieee1394 97208 1 ohci1394 uhci_hcd 32016 0 sis900 20864 0 mii 5504 1 sis900 ehci_hcd 32136 0 usbcore 112640 3 uhci_hcd,ehci_hcd i2c_sis96x 5380 0 i2c_core 20368 1 i2c_sis96x sis_agp 8452 1 agpgart 33096 1 sis_agp shpchp 88676 0 pci_hotplug 26164 1 shpchp nls_utf8 2048 1 ntfs 182288 1 dm_mod 54972 0 ext3 130440 1 jbd 59940 1 ext3 ide_cd 39684 0 cdrom 36896 2 sr_mod,ide_cd fan 4996 0 thermal 14472 0 processor 24252 1 thermal sis5513 15624 0 [permanent] ide_disk 17152 4 ide_core 122380 4 generic,ide_cd,sis5513,ide_disk holger@linux:~> 

Code:

linux:~ # /usr/sbin/sensors-detect

This program will help you determine which I2C/SMBus modules you need to
load to use lm_sensors most effectively. You need to have i2c and
lm_sensors installed before running this program.
Also, you need to be `root', or at least have access to the /dev/i2c-*
files, for most things.
If you have patched your kernel and have some drivers built in, you can
safely answer NO if asked to load some modules. In this case, things may
seem a bit confusing, but they will still work.

It is generally safe and recommended to accept the default answers to all
questions, unless you know what you're doing.

 We can start with probing for (PCI) I2C or SMBus adapters.
 You do not need any special privileges for this.
 Do you want to probe now? (YES/no): y
Probing for PCI bus adapters...
Use driver `i2c-sis96x' for device 00:02.1: Silicon Integrated Systems SMBus Controller
Probe succesfully concluded.

We will now try to load each adapter module in turn.
Module `i2c-sis96x' already loaded.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.

 To continue, we need module `i2c-dev' to be loaded.
 If it is built-in into your kernel, you can safely skip this.
 i2c-dev is not loaded. Do you want to load it now? (YES/no): y
WARNING: /etc/modprobe.conf line 447: ignoring bad line starting with 'modprobe'
WARNING: /etc/modprobe.conf line 449: ignoring bad line starting with 'modprobe'
WARNING: /etc/modprobe.conf line 451: ignoring bad line starting with '/usr/bin/sensors'
 Module loaded succesfully.

 We are now going to do the adapter probings. Some adapters may hang halfway
 through; we can't really help that. Also, some chips will be double detected;
 we choose the one with the highest confidence value in that case.
 If you found that the adapter hung after probing a certain address, you can
 specify that address to remain unprobed. That often
 includes address 0x69 (clock chip).

Next adapter: SiS96x SMBus adapter at 0x0c00
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x08
Client found at address 0x10
Client found at address 0x2d
Probing for `Myson MTP008'... Failed!
Probing for `National Semiconductor LM78'... Failed!
Probing for `National Semiconductor LM78-J'... Failed!
Probing for `National Semiconductor LM79'... Failed!
Probing for `National Semiconductor LM80'... Failed!
Probing for `National Semiconductor LM85 or LM96000'... Failed!
Probing for `Analog Devices ADM1027, ADT7460 or ADT7463'... Failed!
Probing for `SMSC EMC6D100, EMC6D101 or EMC6D102'... Failed!
Probing for `National Semiconductor LM87'... Failed!
Probing for `National Semiconductor LM93'... Failed!
Probing for `Winbond W83781D'... Failed!
Probing for `Winbond W83782D'... Failed!
Probing for `Winbond W83783S'... Failed!
Probing for `Winbond W83791D'... Failed!
Probing for `Winbond W83792D'... Failed!
Probing for `Winbond W83791SD'... Failed!
Probing for `Winbond W83627HF'... Failed!
Probing for `Winbond W83627EHF'... Failed!
Probing for `Asus AS99127F (rev.1)'... Failed!
Probing for `Asus AS99127F (rev.2)'... Failed!
Probing for `Asus ASB100 Bach'... Failed!
Probing for `Winbond W83L784R/AR'... Failed!
Probing for `Winbond W83L785R'... Failed!
Probing for `Genesys Logic GL518SM Revision 0x00'... Failed!
Probing for `Genesys Logic GL518SM Revision 0x80'... Failed!
Probing for `Genesys Logic GL520SM'... Failed!
Probing for `Genesys Logic GL525SM'... Failed!
Probing for `Analog Devices ADM9240'... Failed!
Probing for `Dallas Semiconductor DS1780'... Failed!
Probing for `National Semiconductor LM81'... Failed!
Probing for `Analog Devices ADM1026'... Failed!
Probing for `Analog Devices ADM1025'... Failed!
Probing for `Philips NE1619'... Failed!
Probing for `Analog Devices ADM1024'... Failed!
Probing for `Analog Devices ADM1029'... Failed!
Probing for `Analog Devices ADM1030'... Failed!
Probing for `Analog Devices ADM1031'... Failed!
Probing for `Analog Devices ADM1022'... Failed!
Probing for `Texas Instruments THMC50'... Failed!
Probing for `VIA VT1211 (I2C)'... Failed!
Probing for `ITE IT8712F'... Failed!
Probing for `ITE IT8705F / SiS 950'... Failed!
Probing for `ALi M5879'... Failed!
Client found at address 0x48
Probing for `National Semiconductor LM75'... Failed!
Probing for `National Semiconductor LM77'... Failed!
Probing for `Dallas Semiconductor DS1621'... Failed!
Probing for `Maxim MAX6650/MAX6651'... Failed!
Probing for `National Semiconductor LM92'... Failed!
Probing for `National Semiconductor LM76'... Failed!
Probing for `Maxim MAX6633/MAX6634/MAX6635'... Failed!
Client found at address 0x49
Probing for `National Semiconductor LM75'... Failed!
Probing for `National Semiconductor LM77'... Failed!
Probing for `Dallas Semiconductor DS1621'... Failed!
Probing for `National Semiconductor LM92'... Failed!
Probing for `National Semiconductor LM76'... Failed!
Probing for `Maxim MAX6633/MAX6634/MAX6635'... Failed!
Client at address 0x50 can not be probed - unload all client drivers first!
Client found at address 0x69
Client found at address 0x6a

Some chips are also accessible through the ISA bus. ISA probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan the ISA bus? (YES/no): y
Probing for `National Semiconductor LM78'
  Trying address 0x0290... Failed!
Probing for `National Semiconductor LM78-J'
  Trying address 0x0290... Failed!
Probing for `National Semiconductor LM79'
  Trying address 0x0290... Failed!
Probing for `Winbond W83781D'
  Trying address 0x0290... Failed!
Probing for `Winbond W83782D'
  Trying address 0x0290... Failed!
Probing for `Winbond W83627HF'
  Trying address 0x0290... Failed!
Probing for `Winbond W83627EHF'
  Trying address 0x0290... Failed!
Probing for `Winbond W83697HF'
  Trying address 0x0290... Failed!
Probing for `Silicon Integrated Systems SIS5595'
  Trying general detect... Failed!
Probing for `VIA Technologies VT82C686 Integrated Sensors'
  Trying general detect... Failed!
Probing for `VIA Technologies VT8231 Integrated Sensors'
  Trying general detect... Failed!
Probing for `ITE IT8712F'
  Trying address 0x0290... Failed!
Probing for `ITE IT8705F / SiS 950'
  Trying address 0x0290... Failed!
Probing for `IPMI BMC KCS'
  Trying address 0x0ca0... Failed!
Probing for `IPMI BMC SMIC'
  Trying address 0x0ca8... Failed!

Some Super I/O chips may also contain sensors. Super I/O probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan for Super I/O sensors? (YES/no): y
Probing for `ITE 8702F Super IO Sensors'
  Failed! (skipping family)
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
  Failed! (skipping family)
Probing for `SMSC 47B27x Super IO Fan Sensors'
  Failed! (skipping family)
Probing for `VT1211 Super IO Sensors'
  Failed! (skipping family)
Probing for `Winbond W83627EHF Super IO Sensors'
  Failed! (skipping family)

Do you want to scan for secondary Super I/O sensors? (YES/no): y
Probing for `ITE 8702F Super IO Sensors'
  Failed! (skipping family)
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
  Failed! (skipping family)
Probing for `SMSC 47B27x Super IO Fan Sensors'
  Failed! (skipping family)
Probing for `VT1211 Super IO Sensors'
  Failed! (0x61)
Probing for `Winbond W83627HF Super IO Sensors'
  Failed! (0x61)
Probing for `Winbond W83627THF Super IO Sensors'
  Failed! (0x61)
Probing for `Winbond W83637HF Super IO Sensors'
  Failed! (0x61)
Probing for `Winbond W83697HF Super IO Sensors'
  Failed! (0x61)
Probing for `Winbond W83697SF/UF Super IO PWM'
  Failed! (0x61)
Probing for `Winbond W83L517D Super IO'
  Success... (no hardware monitoring capabilities)
Probing for `Winbond W83627EHF Super IO Sensors'
  Failed! (0x6102)

   

 

AW: SuSE 10.0 goes Netzwerk

Code:

 Sorry, no chips were detected. Either your sensors are not supported, or they are connected to an I2C bus adapter that we do not support. See doc/FAQ, doc/lm_sensors-FAQ.html, or http://www2.lm-sensors.nu/~lm78/cvs/lm_sensors2/doc/lm_sensors-FAQ.html (FAQ #4.24.3) for further information. If you find out what chips are on your board, see http://secure.netroedge.com/~lm78/newdrivers.html for driver status. linux:~ # 

Im Yast sysconfig editor habe ich 2 Module gefunden, lm_sensors
Modul 0 hat den Eintrag: i2c-sis96x
Modul 1 hat den Eintrag: eeprom

 

AW: SuSE 10.0 goes Netzwerk

Code:

linux:~ # modprobe -l fan /lib/modules/2.6.13-15-default/kernel/drivers/acpi/fan.ko

Wenn da was gefunden wird, sollte er sich ja der Lüfter auch irgendwie ansprechen lassen.

Hast du das mal probiert ?

Code:

echo -n 0 > /proc/acpi/fan/FAN1/state
echo -n 0 > /proc/acpi/fan/FAN2/state
echo -n 3 > /proc/acpi/fan/FAN1/state
echo -n 3 > /proc/acpi/fan/FAN2/state

Wenn sich bei einem der Befehle was tut, kannst du das auch in die etc/init.d/boot.local reinschreiben, dann wird das beim booten ausgeführt.

 

AW: SuSE 10.0 goes Netzwerk

Nein, ich habe erstmal mit dem WLAN gekämpft. Muß einem doch gesagt werden,das man das nicht unter "root"rechten machen darf.

So und nu hat sich meine Tastatur unter SuSE verabschiedet, kann mich noch nicht mal mehr einloggen.

speedfan nutzt den SMBus?

Hier die Dateien von speedfan:

speedfanparams.cfg

Code:

TrayFontSize=0
NoMoreTip0001=true
NoMoreTip0002=false
NoMoreTip0003=true
NoMoreTip0004=false
NoMoreTip0005=false
FullOnExit=false
MinimizeOnClose=false
FanDelta=2
UseCelsius=true
DebugMode=true
DellFans=false
UseISA=true
UseSMB=true
StartupHide=true
LastDetect=01507984142578C9E0EF697EF808F709
CLKMBVendor=
CLKMBModel=
CLKLow=
CLKHigh=
LowCPUUsage=10
HighCPUUsage=40
LowCPUTime=10
HighCPUTime=4
AutoClockSet=false
CLIconBack=$1FFFFFFF
CLIconText=$FF
Language=German
LogEnabled=false
LogAddHeader=true
LogDecSep=,
LogMaxDays=5
LogMaxDecs=2
AutoFanSpeed=true
InternetProxy=492F6F65534D343D

speedfansens.cfg

Code:

xxx version 2.01

xxx Link UniqueID=ISA@$290
Name=ISA
Address=$290
xxx end

xxx Link UniqueID=PCI@$0
Name=PCI
Address=$0
xxx end

xxx Link UniqueID=SMBusSiSx30@$B80
Name=SMBus
Address=$B80
xxx end

xxx Link UniqueID=SMART@$0
Name=SMART
Address=$0
xxx end

xxx Sensor UniqueID=Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
Name=Winbond W83L784R
UsedBUS=SiSx30 SMBus
Address=$2D
Link=SMBus
StickyProps=2
Property=66 |Reverse PWM01 logic| set to |OFF|
Property=67 |Reverse PWM02 logic| set to |OFF|
xxx end

xxx Sensor UniqueID=LM75@$48(onSMBusSiSx30@$B80)
Name=LM75
UsedBUS=SiSx30 SMBus
Address=$48
Link=SMBus
StickyProps=0
xxx end

xxx Sensor UniqueID=LM75@$49(onSMBusSiSx30@$B80)
Name=LM75
UsedBUS=SiSx30 SMBus
Address=$49
Link=SMBus
StickyProps=0
xxx end

xxx Sensor UniqueID=SAMSUNG MP0402HS03WJ10Y124545
Name=HD0 (40,1GB)
UsedBUS=SMART
Address=$0
Link=SMART
StickyProps=0
xxx end

xxx the end

xxx Pwm 1 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=Speed01
active=true
min=40
max=51
variate=true
xxx end

xxx Pwm 2 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=Speed02
active=true
min=30
max=53
variate=true
xxx end

xxx Temp 1 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=Temp1
active=true
wanted=50
warning=60
offset=0
intray=false
UsedPwms=1
pwm=1 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
logged=false
xxx end

xxx Temp 1 from LM75@$48(onSMBusSiSx30@$B80)
name=Temp
active=true
wanted=58
warning=65
offset=0
intray=true
UsedPwms=1
pwm=2 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
logged=false
xxx end

xxx Temp 1 from LM75@$49(onSMBusSiSx30@$B80)
name=Temp
active=false
wanted=40
warning=50
offset=0
intray=false
UsedPwms=0
logged=false
xxx end

xxx Temp 1 from SAMSUNG MP0402HS03WJ10Y124545
name=HD0
active=true
wanted=40
warning=50
offset=0
intray=false
UsedPwms=0
logged=false
xxx end

xxx Fan 1 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=Fan01
active=true
logged=false
xxx end

xxx Fan 2 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=Fan02
active=true
logged=false
xxx end

xxx Volt 1 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=VCORE
active=false
logged=false
xxx end

xxx Volt 2 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=VBAT
active=true
logged=false
xxx end

xxx Volt 3 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=+3.3V
active=true
logged=false
xxx end

xxx Volt 4 from Winbond W83L784R@$2D(onSMBusSiSx30@$B80)
name=+5V
active=true
logged=false
xxx end

Code: