D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

Anzeige

AW: D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

Das problem ist nicht, dass ich kein nullmodem habe ... sondern dass ich die dbox aus meinem hifi-fernsehturm rauspfriemeln muss, um sie in meinem arbeitszimmer an den pc zu hängen ...
Ich hatte das auch alles schon mal am laufen, vor gut einem jahr um linux auf die box zu kriegen, nur isses halt einfacher übers lan draufzukommen, da das ja alles noch völlig problemlos funktioniert.
Was auch einwandfrei noch geht, ist ein sendersuchlauf ... schon komisch

 

AW: D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

hier ein bootlog:

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-33.0e.03.07.00.00-d9
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 160684
verify sig: 263
Branching to 0x40000


U-Boot 1.1.2 (Tuxbox) (Mar 16 2005 - 20:36:54)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 627248 bytes loaded to 0x100000
......................................................................
Un-Protected 70 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 627184 Bytes = 612.5 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (ImageTeam@yadi.org) (gcc version 3.3.5) #2 Mi Mr 16
21:18:16 CET 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30904k available (1068k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:14:a0:6c
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/cable_ves1820.o
insmod: Warning: kernel-module version mismatch
/lib/modules/2.4.27-dbox2/misc/cable_ves1820.o was compiled for kernel v
ersion 2.4.25-dbox2
while this kernel is version 2.4.27-dbox2
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
Using /lib/modules/2.4.27-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.6 2005/02/08 22:30:05 mogway Exp $
Yadi Release vom 16.03.2005 19:53 - Image-Version 2.1.0.0
Networkcfg eth0: 192.168.0.3/255.255.255.0 gw 192.168.0.1
Startmode: Bootmenu - HWSff
Using /lib/modules/2.4.27-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.27-dbox2/kernel/fs/cifs/cifs.o
Starting pid 91, console /dev/console: '/etc/init.d/start'

 

AW: D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

Der Rest:

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.181 2005/03/
08 13:39:08 metallica Exp $
caching 504 hours
events are old 180min after their end time
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.370 2005/03/14 19:58:48 mws Exp $
[zapit] PMT update enabled
avia_gt_core: masking unhandled irq reg 0 bit 7
/var/tuxbox/config/zapit/bouquets.xml: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[camd] no card is in slot #2
[camd] no card is in slot #1
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[neutrino] initialized everything
SPTS, queue 0 extended.
avia_gt_core: masking unhandled irq reg 1 bit 15
[timeThread] time(): 04.09.2005 11:50:12, tim: Sun Sep 4 11:50:12 2005
[timeThread] time(): 04.09.2005 11:50:41, tim: Sun Sep 4 11:50:41 2005
avia_av: status timeout - chip didn't accept command 0x231
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
SPTS, queue 0 extended.
avia_av: status timeout - chip didn't accept command 0x231
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
SPTS, queue 0 extended.
SPTS, queue 0 extended.
SPTS, queue 0 extended.
avia_av: status timeout - chip didn't accept command 0x231
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
SPTS, queue 0 extended.
zapit shot down
Waiting for controld (max. 9 seconds)
avia_av: status timeout - chip didn't accept command 0x231
Waiting for zapit (max. 8 seconds)
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
Starting pid 151, console /dev/console: '/bin/switch'
CXA2092 found
The system is going down NOW !![nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power

Die Meldungen "avia_av: status timeout - chip didn't accept command 0x231" erscheinen sobald ich die Sender wechsle.
Deutet das auf einen kaputten Chip hin?

 

AW: D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

Spiel doch noch mal die ucodes neu ein. Meine erste Vermutung ist, dass diese Dateien im Flash beschädigt wurden und die Prüfsumme nicht mehr stimmt. Damit kann der AViA keine Kommandos mehr ausführen.

 

AW: D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

danke für den tip mit den ucodes ... hat leider auch nichts gebracht

jetzt versuch ich grad mal, ob ich noch übers netz aufnehmen kann, was scheinbar auch funktioniert ... und nu?

 

AW: D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

Denn reflash mal komplett. Ansonsten ist der AVIA-Käfer hin. Abgebrannt.

 

AW: D-Box 2 nur noch kurz grünes Bild - kein Sender funktioniert mehr

hab ich auch schon gemacht ... hat leider nix gebracht
... jetzt nutz ich die box halt noch zum streamen (solange es noch geht)
danke für die tips !