1. Cookies optimieren die Bereitstellung unserer Dienste. Mit der Nutzung unserer Dienste erklärst Du dich damit einverstanden, dass wir Cookies verwenden. Weitere Informationen
    Information ausblenden
  2. Willkommen im Forum von DIGITAL FERNSEHEN - dem führenden Portal für digitales Fernsehen, Medien und Entertainment. Wenn du hier neu bist, schau dich ruhig etwas um und melde dich an, um am Forengeschehen teilnehmen zu können.
    Information ausblenden

dbox2 mit jtg findet keine Kanäle // hoher BER (>24.000)

Dieses Thema im Forum "d-box 1 und d-box 2" wurde erstellt von jens.mac, 26. Mai 2006.

  1. jens.mac

    jens.mac Neuling

    Registriert seit:
    26. Mai 2006
    Beiträge:
    2
    Zustimmungen:
    0
    Punkte für Erfolge:
    1
    Anzeige
    Meine nokia dbox2 findet keine Kanäle. Nach manueller Einstellung der Kanllisten, zeigen mir die technischen Info nur an, dass BER ca. bei 24.000 liegt.
    Anbei habe ich mal das Bootlog hier angehängt. Vielleicht fällt jemandem etwas dazu ein, da ich selber keinen Vergleich zu einer funktionierenden dbox mit jtg habe.
    Vielen Dank für alle Tipps.

    Gruß Jens
    PS: Alternative Receiver wie pace funktionieren ohne Probleme.

    Bootlog:
    ...
    ## Booting image at 00100000 ...
    Image Name: dbox2
    Image Type: PowerPC Linux Kernel Image (gzip compressed)
    Data Size: 656827 Bytes = 641.4 kB
    Load Address: 00000000
    Entry Point: 00000000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
    Linux version 2.4.32-dbox2 (vom Jtg-Team) (gcc version 3.4.4) #4 Thu Dec 22 23:
    23:45 CET 2005
    On node 0 totalpages: 8192
    zone(0): 8192 pages.
    zone(1): 0 pages.
    zone(2): 0 pages.
    Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=squashfs
    Decrementer Frequency = 252000000/60
    m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
    m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
    Console: colour dummy device 80x25
    Calibrating delay loop... 66.96 BogoMIPS
    Memory: 30856k available (1112k kernel code, 340k data, 60k init, 0k highmem)
    Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
    Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
    Mount cache hash table entries: 512 (order: 0, 4096 bytes)
    Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
    Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
    POSIX conformance testing by UNIFIX
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
    devfs: boot_options: 0x1
    JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
    Squashfs 2.2-r2 (released 2005/09/0[​IMG] (C) 2002-2005 Phillip Lougher
    i2c-core.o: i2c core module version 2.6.1 (20010830)
    i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
    CPM UART driver version 0.04
    ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
    pty: 256 Unix98 ptys configured
    eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1c:55:55
    loop: loaded (max 8 devices)
    D-Box 2 flash driver (size->0x800000 mem->0x10000000)
    D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
    Intel/Sharp Extended Query Table at 0x0035
    cfi_cmdset_0001: Erase suspend on write enabled
    Creating 6 MTD partitions on "D-Box 2 flash memory":
    0x00000000-0x00020000 : "BR bootloader"
    0x00020000-0x00040000 : "FLFS (U-Boot)"
    0x00040000-0x006a0000 : "root (SquashFS)"
    0x006a0000-0x00800000 : "var (JFFS2)"
    0x00020000-0x00800000 : "Flash without bootloader"
    0x00000000-0x00800000 : "Complete Flash"
    Linux video capture interface: v1.00
    mice: PS/2 mouse device common for all mice
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 2048 bind 4096)
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    VFS: Mounted root (squashfs filesystem) readonly.
    Mounted devfs on /dev
    Freeing unused kernel memory: 60k init
    init started: BusyBox v1.01 (2005.11.08-18:34+0000) multi-call bThu Jan 1 12:0
    0:00 CET 1970
    Using /lib/modules/2.4.32-dbox2/misc/event.o
    event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
    Using /lib/modules/2.4.32-dbox2/misc/tuxbox.o
    Using /lib/modules/2.4.32-dbox2/misc/dvb-core.o
    Using /lib/modules/2.4.32-dbox2/misc/dbox2_i2c.o
    [i2c-8xx]: mpc 8xx i2c init
    [i2c-8xx]: adapter: 0
    Using /lib/modules/2.4.32-dbox2/misc/dbox2_fp.o
    Using /lib/modules/2.4.32-dbox2/misc/dbox2_fp_input.o
    Using /lib/modules/2.4.32-dbox2/misc/avs.o
    Using /lib/modules/2.4.32-dbox2/misc/saa7126.o
    Using /lib/modules/2.4.32-dbox2/misc/cam.o
    $Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
    Using /lib/modules/2.4.32-dbox2/misc/dvb_i2c_bridge.o
    Using /lib/modules/2.4.32-dbox2/misc/avia_napi.o
    $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
    DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
    dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
    Using /lib/modules/2.4.32-dbox2/misc/cam_napi.o
    $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
    Using /lib/modules/2.4.32-dbox2/misc/dbox2_fp_napi.o
    Using /lib/modules/2.4.32-dbox2/misc/avia_av.o
    avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
    avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
    avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
    Using /lib/modules/2.4.32-dbox2/misc/avia_gt.o
    avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
    avia_gt_core: autodetecting chip type... GTX
    avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
    avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
    avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
    avia_gt_core: masking unhandled irq reg 1 bit 11
    avia_gt_core: masking unhandled irq reg 1 bit 13
    avia_gt_ucode: loaded ucode vB107
    avia_gt_ucode: ucode section filters disabled.
    avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
    avia_gt_core: masking unhandled irq reg 0 bit 6
    avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
    avia_gt_gv: set_input_size (width=720, height=576)
    avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
    avia_gt_pcm_set_rate(44100)
    avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
    avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
    avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
    avia_gt_core: Loaded AViA eNX/GTX driver
    Using /lib/modules/2.4.32-dbox2/misc/avia_gt_fb.o
    avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    Console: switching to colour frame buffer device 82x32
    avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
    Using /lib/modules/2.4.32-dbox2/misc/lcd.o
    lcd.o: init lcd driver module
    lcd.o: found KS0713/SED153X lcd interface
    jtginfo $Id: jtginfo.c,v 1.5 2005/10/25 15:20:33 jtgriker Exp $
    Using /lib/modules/2.4.32-dbox2/misc/avia_gt_lirc.o
    avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
    avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
    Using /lib/modules/2.4.32-dbox2/misc/avia_gt_oss.o
    avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
    avia_gt_pcm_set_rate(44100)
    Using /lib/modules/2.4.32-dbox2/misc/avia_gt_v4l2.o
    avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
    Using /lib/modules/2.4.32-dbox2/misc/ves1820.o
    DVB: VES1820(0): pwm=0x48
    DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
    Using /lib/modules/2.4.32-dbox2/misc/ves1x93.o
    Using /lib/modules/2.4.32-dbox2/misc/avia_av_napi.o
    avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
    Using /lib/modules/2.4.32-dbox2/misc/avia_gt_napi.o
    avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
    Using /lib/modules/2.4.32-dbox2/misc/dvb2eth.o
    Using /lib/modules/2.4.32-dbox2/misc/aviaEXT.o
    $Id: sectionsd.cpp,v 1.216 2005/12/18 07:49:16 metallica Exp $
    caching 504 hours
    events are old 180min after their end time
    [ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
    $Id: zapit.cpp,v 1.384 2005/11/28 05:19:39 metallica Exp $
    avia_gt_core: masking unhandled irq reg 0 bit 7
    [getservices] /var/tuxbox/config/zapit/myservices.xml found.
    [getservices] dup transponder id 1 onid 85
    [getservices] dup transponder id 3 onid 85
    [getservices] dup transponder id 4 onid 85
    [getservices] dup transponder id 11 onid 85
    [camd] ca system id: 1722
    $Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

    [controld] Boxtype detected: (1, Nokia D-BOX2)
    [nhttpd] Neutrino HTTP-Server starting..
    [LCDFONT] initializing core...
    [LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
    [LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
    [LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
    [LCDFONT] Intializing font cache...
    [neutrino] frameBuffer Instance created
    812k video mem
    avia_gt_gv: set_input_mode (mode=2)
    avia_gt_gv: set_input_size (width=720, height=576)
    [neutrino] Software update enabled
    [neutrino] enable flash
    [lcdd] time-skin not found -> using default...
    [lcdd] weekday-skin not found -> using default...
    [lcdd] date-skin not found -> using default...
    [lcdd] month-skin not found -> using default...
    [LCDFONT] initializing core...
    [LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
    [LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
    [LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
    [LCDFONT] Intializing font cache...
    [LCDFONT] FTC_Face_Requester (Fix15/Bold)
    [LCDFONT] FTC_Face_Requester (Fix14/Bold)
    /dev/input/event1: No such file or directory
    [neutrino] menue setup
    [controld] setting VideoFormat to auto
    loading locales: scandir: No such file or directory
    [neutrino] registering as event client
    [neutrino] initialized everything
    [dmx.cpp:read:184] read(fd, buf, n): Connection timed out
    zap failed!
    [sectionsd] getUTC: read: Connection timed out
    [LCDFONT] FTC_Face_Requester (Fix12/Regular)
    [controld] setting VideoFormat to auto
    [dmx.cpp:read:184] read(fd, buf, n): Connection timed out
    zap failed!
    [sectionsd] getUTC: read: Connection timed out
    [sectionsd] getUTC: read: Connection timed out
     
  2. Gorcon

    Gorcon Kanzler Premium

    Registriert seit:
    15. Januar 2001
    Beiträge:
    148.612
    Zustimmungen:
    26.880
    Punkte für Erfolge:
    273
    Technisches Equipment:
    VU+ Uno 4K SE mit Neutrino HD + VTi
    AW: dbox2 mit jtg findet keine Kanäle // hoher BER (>24.000)

    Hi

    Ich gehe mal davon aus das Du Kabel hast.
    Wie sieht denn Dein durchgeschleiftes analog Bild aus?

    Gruß Gorcon
     
  3. jens.mac

    jens.mac Neuling

    Registriert seit:
    26. Mai 2006
    Beiträge:
    2
    Zustimmungen:
    0
    Punkte für Erfolge:
    1
    AW: dbox2 mit jtg findet keine Kanäle // hoher BER (>24.000)

    Sorry, ja ist 'ne Kabelbox.
    Die durchgeschleiften analogen Programme funktionieren pächtig.

    Finde nur eben keine Kanäle :confused:

    Gruß Jens